Water hardness in Guilford County, NC
Water in Guilford County is soft, with a median of 40 mg/L (2.3 grains per gallon) across 28 monitoring sites.
Guilford County water at a glance
- HardnessSoft (40 mg/L, 2.3 gpg, local measurements). A water softener isn't needed.Water heater care →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 40 mg/L means at home
- Water softener: A water softener is generally not needed. Soft water rarely causes scale.
- Dishwasher: set the water hardness to about 2.3 gpg (2.2 °dH), which is the lowest hardness setting (or softener off).
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Guilford County
Prefilled with Guilford County's measured local hardness of 40 mg/L (2.3 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Guilford County on the North Carolina map
Cities and communities in Guilford County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Greensboro | 48 | Soft | 16 sites within 10 miles |
| High Point | 44 | Soft | 18 sites within 10 miles |
| Archdale | 45 | Soft | 17 sites within 10 miles |
| Summerfield | 30 | Soft | 8 sites within 10 miles |
| Oak Ridge | 34 | Soft | 11 sites within 10 miles |
| Stokesdale | 32 | Soft | 8 sites within 10 miles |
| Pleasant Garden | 63 | Moderately hard | 10 sites within 10 miles |
| Forest Oaks (CDP) | 74 | Moderately hard | 8 sites within 10 miles |
| Jamestown | 42 | Soft | 17 sites within 10 miles |
| McLeansville (CDP) | 71 | Moderately hard | 11 sites within 10 miles |
| Sedalia | 61 | Moderately hard | 11 sites within 10 miles |
| Whitsett | 60 | Soft | 12 sites within 10 miles |
Water quality in Guilford County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Greensboro | City of Greensboro | 9 found (PFOA 5.6 / PFOS 35.6 ppt) | 0 lead · 67,123 unknown | None |
| High Point | City of High Point | 6 found (PFOA 4.2 / PFOS 11 ppt) | 0 lead · 0 unknown | 1 |
| Archdale | City of Archdale | 8 found (PFOA 5.6 / PFOS 10.6 ppt) | 0 lead · 4,515 unknown | None |
| Summerfield | the Vineyards AT Summerfield | Not tested | 0 lead · 0 unknown | None |
| Oak Ridge | the Estates of Oak Ridge Lake | Not tested | 0 lead · 0 unknown | None |
| Stokesdale | Town of Stokesdale | None detected | 0 lead · 0 unknown | 1 |
| Pleasant Garden | Clapp`S Nursing CTR-Appomattox | Not tested | 0 lead · 0 unknown | None |
| Jamestown | Town of Jamestown | 8 found (PFOA 5.9 / PFOS 10.4 ppt) | 0 lead · 1,048 unknown | None |
| Whitsett | Rock Creek MH Village No 2 | Not tested | 0 lead · 0 unknown | 1 |
Neighboring counties
- Rockingham County36 mg/L
- Alamance County42 mg/L
- Randolph County48 mg/L
- Forsyth County36 mg/L
- Davidson County46 mg/L
- Caswell County33 mg/L
North Carolina
The statewide median is 33 mg/L (soft) from 1,749 sites.
North Carolina hardness map →Hardness scale
What to read next
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.