Water hardness in Howard County, MD

Water in Howard County is soft, with a median of 56 mg/L (3.2 grains per gallon) across 8 monitoring sites.

about the same as the Maryland median (56 mg/L) 15th hardest of 24 counties
56mg/L
3.2 grains per gallon
Soft

Howard County water at a glance

  • HardnessSoft (56 mg/L, 3.2 gpg, local measurements). A water softener isn't needed.Water heater care →
  • Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →

What 56 mg/L means at home

  • Water softener: A water softener is generally not needed. Soft water rarely causes scale.
  • Dishwasher: set the water hardness to about 3.2 gpg (3.1 °dH), which is the lowest hardness setting (or softener off).
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites8
Lab samples9
Sample years2001–2019
Middle 50% of sites23–73 mg/L
Groundwater (wells, springs)56 mg/L · 8 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Howard County

Prefilled with Howard County's measured local hardness of 56 mg/L (3.3 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

Howard County on the Maryland map

Washington CountyAllegany CountyQueen Anne's CountyCharles CountyAnne Arundel CountyGarrett CountySt. Mary's CountySomerset CountyCaroline CountyWicomico CountyCecil CountyHarford CountyBaltimore cityDorchester CountyCalvert CountyBaltimore CountyCarroll CountyFrederick CountyMontgomery CountyWorcester CountyPrince George's CountyKent CountyTalbot County

Cities and communities in Howard County

PlaceMedian mg/LClassBased on
Columbia (CDP) 50 Soft 15 sites within 10 miles
Ellicott City (CDP) 76 Moderately hard 24 sites within 10 miles
Ilchester (CDP) 50 Soft 23 sites within 10 miles
Elkridge (CDP) 49 Soft 21 sites within 10 miles
Jessup (CDP) 23 Soft 21 sites within 10 miles
Savage (CDP) 23 Soft 21 sites within 10 miles
North Laurel (CDP) 16 Soft 18 sites within 10 miles
Fulton (CDP) 32 Soft 14 sites within 10 miles
Highland (CDP) 55 Soft 9 sites within 10 miles
Lisbon (CDP) 51 Soft 11 sites within 10 miles
Scaggsville (CDP) 32 Soft 14 sites within 10 miles

Neighboring counties

Maryland

The statewide median is 56 mg/L (soft) from 1,412 sites.

Maryland hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next