Water hardness in Seattle, WA

Tap water in Seattle is soft: about 28 mg/L (1.6 grains per gallon), ranging from 27 to 30 mg/L, as reported by Seattle Public Utilities.

62% softer than the Washington median (74 mg/L) 111th hardest of 122 Washington towns Population 755,078
28mg/L
1.6 grains per gallon
Soft

Utility-reported value. May 2026 quarterly analysis of Cedar River supply: 1.55 to 1.73 grains per gallon. Source: Seattle Public Utilities (2026). Local groundwater and surface water around Seattle measures harder (median 103 mg/L), which matters if you are on a private well.

Seattle tap water at a glance

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 28 mg/L means at home

  • Water softener: A water softener is generally not needed. Soft water rarely causes scale.
  • Dishwasher: set the water hardness to about 1.6 gpg (1.6 °dH), which is the lowest hardness setting (or softener off).
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Local source water measurements

Median of nearby sites103 mg/L
Monitoring sites9
Lab samples81
Sample years2001–2015
Middle 50% of sites78–116 mg/L
Groundwater (wells, springs)27 mg/L · 2 sites
Surface water (rivers, lakes)110 mg/L · 7 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Seattle

Prefilled with Seattle's utility-reported hardness of 28 mg/L (1.6 gpg).

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Seattle tap water

Seattle Public Utilities is the main public water system for Seattle. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 8 samples taken Jun 2023 – Dec 2023. No PFAS were found at or above EPA's minimum reporting levels.

Other water systems serving parts of Seattle

Water systemPFAS detectedHighest PFOA / PFOSTested
Tukwila Water Department
serves over 10,000 people
None detected — Mar 2024 – Dec 2024
King County Water District #20
serves over 10,000 people
None detected — Mar 2024 – Dec 2024
Skyway Water & Sewer
serves over 10,000 people
None detected — May 2023 – Feb 2024
North City Water District
serves over 10,000 people
None detected — Jul 2024 – Apr 2025
Northshore Utility District
serves over 10,000 people
None detected — Mar 2023 – Dec 2023

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Seattle

Seattle Public Utilities reported 206,340 service lines (the pipes connecting homes to the water main) in its inventory. It reported no lead or galvanized lines requiring replacement.

0lead (0%)
0galvanized requiring replacement
0unknown material (0%)
206,340not lead (100%)

Other water systems serving parts of Seattle

Water systemService linesTotal
Tukwila Water Department0 lead · 0 galvanized · 2,110 unknown2,401
King County Water District #200 lead · 141 galvanized · 0 unknown10,748
Skyway Water & Sewer0 lead · 0 galvanized · 3,435 unknown3,435
North City Water District0 lead · 459 galvanized · 41 unknown8,138
Northshore Utility District0 lead · 0 galvanized · 2,001 unknown22,883

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Seattle drinking water violations

EPA records show no health-based violations for Seattle Public Utilities since 2016.

Other water systems serving parts of Seattle

Water systemHealth-based violationsMonitoring/reporting
Tukwila Water DepartmentNone0
King County Water District #20None0
Skyway Water & SewerNone2
North City Water DistrictNone0
Northshore Utility DistrictNone0

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Seattle

SiteTypeDistanceMedianSamplesYears
LONGFELLOW CREEK AB GENESEE ST NR WEST SEATTLE, WA
USGS Washington Water Science Center
Stream 3.9 mi142 mg/L102015
THORNTON CREEK NEAR SEATTLE, WA
USGS Washington Water Science Center
Stream 6.3 mi103 mg/L192001–2015
PIPERS CREEK AT CARKEEK PARK, AT SEATTLE, WA
USGS Washington Water Science Center
Stream 6.5 mi116 mg/L102015
MERCER CREEK NEAR BELLEVUE, WA
USGS Washington Water Science Center
Stream 8 mi110 mg/L102015
COAL CREEK AT BELLEVUE, WA
USGS Washington Water Science Center
Stream 8.6 mi162 mg/L102015
JUANITA CREEK NEAR KIRKLAND, WA
USGS Washington Water Science Center
Stream 8.8 mi93 mg/L102015

Water hardness in towns near Seattle

TownDistanceMedianClass
Mercer Island7 mi 80 mg/LModerately hard
Bainbridge Island7 mi 106 mg/LModerately hard
White Center8 mi 67 mg/LModerately hard
Kirkland9 mi 93 mg/LModerately hard
Bellevue9 mi 71 mg/LModerately hard
Shoreline10 mi 98 mg/LModerately hard
Burien10 mi 70 mg/LModerately hard
Bryn Mawr-Skyway10 mi 87 mg/LModerately hard
Lake Forest Park10 mi 93 mg/LModerately hard
Kenmore10 mi 91 mg/LModerately hard

King County

Seattle is in King County, where the median is 61 mg/L (moderately hard) across 34 sites.

See all of King County →

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Seattle, WA water: common questions

Do I need a water softener in Seattle?

Probably not. Seattle's tap water is 1.6 gpg (28 mg/L, utility-reported), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable.When a softener helps →

Who supplies Seattle's drinking water?

The main public water system serving Seattle in EPA records is Seattle Public Utilities. Some neighborhoods may be served by a different system, so check the name on your water bill.Seattle Public Utilities water quality report →

Do I need a water filter in Seattle?

Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next