Water hardness in Bellevue, WA

Water in Bellevue is moderately hard, with a median of 71 mg/L (4.1 grains per gallon) across 13 monitoring sites within 10 miles.

about the same as the Washington median (74 mg/L) 40th hardest of 122 Washington towns Population 151,574
71mg/L
4.1 grains per gallon
Moderately hard

Large city utilities sometimes soften, blend or import water from distant reservoirs, so tap water in Bellevue can differ from local source water. Your utility's annual Consumer Confidence Report lists the exact tap value.

Bellevue tap water at a glance

  • HardnessModerately hard (71 mg/L, 4.1 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →
  • PFASNone found in EPA's nationwide testing of the main water system.PFAS results →
  • Lead pipesNo known lead lines; 9,739 lines are still of unknown material.Check your own pipe →
  • ViolationsNo health-based violations since 2016.EPA record →

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 71 mg/L means at home

  • Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
  • Dishwasher: set the water hardness to about 4.1 gpg (4 °dH), which is a low-to-medium hardness setting.
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites13
Lab samples132
Sample years2000–2016
Middle 50% of sites51–93 mg/L
Groundwater (wells, springs)50 mg/L · 2 sites
Surface water (rivers, lakes)78 mg/L · 11 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Bellevue

Prefilled with Bellevue's measured local hardness of 71 mg/L (4.2 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Bellevue tap water

City of Bellevue is the main public water system for Bellevue. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 8 samples taken Jan 2024 – Oct 2024. No PFAS were found at or above EPA's minimum reporting levels.

Other water systems serving parts of Bellevue

Water systemPFAS detectedHighest PFOA / PFOSTested
King County Water District No 90
serves over 10,000 people
None detected — Sep 2024 – Jun 2025
Issaquah Water System
serves over 10,000 people
None detected — Sep 2024 – Jun 2025
Woodinville Water District
serves over 10,000 people
None detected — Sep 2024 – Jun 2025
Coal Creek Utility District
serves over 10,000 people
None detected — Jan 2024 – Oct 2024
City of Kirkland
serves over 10,000 people
None detected — Sep 2024 – Jun 2025

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Bellevue

City of Bellevue reported 40,476 service lines (the pipes connecting homes to the water main) in its inventory. It reported no known lead lines, but 9,739 lines are still of unknown material.

0lead (0%)
0galvanized requiring replacement
9,739unknown material (24%)
30,737not lead (76%)

Other water systems serving parts of Bellevue

Water systemService linesTotal
King County Water District No 900 lead · 0 galvanized · 323 unknown8,198
Issaquah Water System0 lead · 0 galvanized · 0 unknown9,402
Woodinville Water District0 lead · 0 galvanized · 0 unknown14,831
Coal Creek Utility District0 lead · 0 galvanized · 0 unknown3,991
City of Kirkland0 lead · 82 galvanized · 0 unknown13,332

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Bellevue drinking water violations

EPA records show no health-based violations for City of Bellevue since 2016.

Other water systems serving parts of Bellevue

Water systemHealth-based violationsMonitoring/reporting
King County Water District No 90None2
Issaquah Water SystemNone0
Woodinville Water DistrictNone0
Coal Creek Utility DistrictNone1
City of KirklandNone0

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Bellevue

SiteTypeDistanceMedianSamplesYears
MERCER CREEK NEAR BELLEVUE, WA
USGS Washington Water Science Center
Stream 1.2 mi110 mg/L102015
COAL CREEK AT BELLEVUE, WA
USGS Washington Water Science Center
Stream 2.4 mi162 mg/L102015
MAY CREEK BELOW HONEY DEW CREEK NEAR RENTON, WA
USGS Washington Water Science Center
Stream 5.7 mi78 mg/L102015
BEAR CREEK AT UNION HILL RD AT REDMOND, WA
USGS Washington Water Science Center
Stream 5.8 mi65 mg/L102015
NORTH FORK ISSAQUAH CREEK AT ISSAQUAH, WA
USGS Washington Water Science Center
Stream 6.8 mi82 mg/L102015
E FORK ISSAQUAH CR ABV 3RD AVE NE AT ISSAQUAH, WA
USGS Washington Water Science Center
Stream 7.4 mi45 mg/L102015

Water hardness in towns near Bellevue

TownDistanceMedianClass
Mercer Island4 mi 80 mg/LModerately hard
Newcastle5 mi 65 mg/LModerately hard
Sammamish6 mi 70 mg/LModerately hard
Redmond6 mi 73 mg/LModerately hard
Issaquah6 mi 65 mg/LModerately hard
Kirkland7 mi 93 mg/LModerately hard
Bryn Mawr-Skyway8 mi 87 mg/LModerately hard
Renton8 mi 56 mg/LSoft
Union Hill-Novelty Hill9 mi 70 mg/LModerately hard
East Renton Highlands9 mi 52 mg/LSoft

King County

Bellevue is in King County, where the median is 61 mg/L (moderately hard) across 34 sites.

See all of King County →

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Bellevue, WA water: common questions

Do I need a water softener in Bellevue?

Probably not. Water measured around Bellevue is 4.1 gpg (71 mg/L, measured locally), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable. If spotting bothers you, about 8,000 grains of capacity covers a 3-person home between weekly regenerations.Size it for your household →

Who supplies Bellevue's drinking water?

The main public water system serving Bellevue in EPA records is City of Bellevue. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →

Do I need a water filter in Bellevue?

Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next