Water hardness in Marysville, WA
Water in Marysville is soft, with a median of 29 mg/L (1.7 grains per gallon) across 31 monitoring sites within 10 miles.
Marysville tap water at a glance
- HardnessSoft (29 mg/L, 1.7 gpg, local measurements). A water softener isn't needed.Water heater care →
- PFASNone found in EPA's nationwide testing of the main water system.PFAS results →
- Lead pipesNo lead service lines reported.Details →
- ViolationsNo health-based violations since 2016.EPA record →
Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?
What 29 mg/L means at home
- Water softener: A water softener is generally not needed. Soft water rarely causes scale.
- Dishwasher: set the water hardness to about 1.7 gpg (1.6 °dH), which is the lowest hardness setting (or softener off).
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Marysville
Prefilled with Marysville's measured local hardness of 29 mg/L (1.7 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
PFAS in Marysville tap water
Marysville Utilities is the main public water system for Marysville. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 16 samples taken Mar 2023 – Dec 2023. No PFAS were found at or above EPA's minimum reporting levels.
Other water systems serving parts of Marysville
| Water system | PFAS detected | Highest PFOA / PFOS | Tested |
|---|---|---|---|
| Arlington Water Dept serves over 10,000 people | PFHxS | — | Feb 2023 – Dec 2023 |
| City of Everett Public Works Dept. serves over 10,000 people | None detected | — | Feb 2023 – Nov 2023 |
| Sno Pud 1 - Lake Stevens serves over 10,000 people | None detected | — | Jan 2024 – Dec 2024 |
| City of Stanwood Water Dept serves over 10,000 people | None detected | — | May 2024 – Nov 2024 |
What these PFAS levels mean → Which water filters remove PFAS →
Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology
Lead pipes in Marysville
Marysville Utilities reported 23,199 service lines (the pipes connecting homes to the water main) in its inventory. It reported no lead or galvanized lines requiring replacement.
Other water systems serving parts of Marysville
| Water system | Service lines | Total |
|---|---|---|
| City of Arlington | 0 lead · 0 galvanized · 983 unknown | 5,774 |
| City of Everett Public Works Dept. | 0 lead · 0 galvanized · 0 unknown | 29,738 |
| Sno Pud 1 - Lake Stevens | 0 lead · 0 galvanized · 0 unknown | 21,499 |
| City of Stanwood Water Dept | 0 lead · 0 galvanized · 1,240 unknown | 3,159 |
How to tell if your home has a lead pipe → Lead pipes in every state →
As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology
Marysville drinking water violations
EPA records show no health-based violations for Marysville Utilities since 2016. It also had 4 monitoring or reporting violations (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.
Other water systems serving parts of Marysville
| Water system | Health-based violations | Monitoring/reporting |
|---|---|---|
| Arlington Water Dept | None | 0 |
| City of Everett Public Works Dept. | None | 2 |
| Sno Pud 1 - Lake Stevens | None | 2 |
| City of Stanwood Water Dept | None | 0 |
Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology
Monitoring sites closest to Marysville
| Site | Type | Distance | Median | Samples | Years |
|---|---|---|---|---|---|
| 30N/05E-06Q03 SU-018 USGS Washington Water Science Center | Well | 3.4 mi | 112 mg/L | 1 | 2016 |
| TULALIP CREEK NEAR TULALIP, WA USGS Washington Water Science Center | Stream | 6.2 mi | 66 mg/L | 4 | 2015 |
| Brenner Creek (Upper) Stillaguamish Tribe of Indians of Washington (Tribal) | River/Stream | 6.9 mi | 37 mg/L | 28 | 2010–2015 |
| Main Stilly Stillaguamish Tribe of Indians of Washington (Tribal) | River/Stream | 7 mi | 25 mg/L | 719 | 2000–2008 |
| Portage Cr @ 80th Ave Stillaguamish Tribe of Indians of Washington (Tribal) | River/Stream | 7.1 mi | 23 mg/L | 385 | 2003–2008 |
| Brenner Creek (Lower) Stillaguamish Tribe of Indians of Washington (Tribal) | River/Stream | 7.1 mi | 37 mg/L | 28 | 2010–2015 |
Water hardness in towns near Marysville
| Town | Distance | Median | Class |
|---|---|---|---|
| Lake Stevens | 6 mi | 37 mg/L | Soft |
| Arlington | 6 mi | 36 mg/L | Soft |
| Everett | 8 mi | 66 mg/L | Moderately hard |
| Snohomish | 11 mi | 38 mg/L | Soft |
| Eastmont | 13 mi | 70 mg/L | Moderately hard |
| Mukilteo | 13 mi | 31 mg/L | Soft |
| Silver Firs | 15 mi | 70 mg/L | Moderately hard |
| Mill Creek | 15 mi | 82 mg/L | Moderately hard |
| North Lynnwood | 17 mi | 82 mg/L | Moderately hard |
| Martha Lake | 17 mi | 88 mg/L | Moderately hard |
Snohomish County
Marysville is in Snohomish County, where the median is 31 mg/L (soft) across 99 sites.
See all of Snohomish County →Washington
The statewide median is 74 mg/L (moderately hard) from 890 sites.
Washington hardness map →Marysville, WA water: common questions
Do I need a water softener in Marysville?
Probably not. Water measured around Marysville is 1.7 gpg (29 mg/L, measured locally), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable.When a softener helps →
Who supplies Marysville's drinking water?
The main public water system serving Marysville in EPA records is Marysville Utilities. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →
Do I need a water filter in Marysville?
Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →
Hardness scale
What to read next
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.