Water hardness in Burlington, WA

Water in Burlington is soft, with a median of 9 mg/L (0.5 grains per gallon) across Skagit County.

88% softer than the Washington median (74 mg/L) 122nd hardest of 122 Washington towns Population 10,358
9mg/L
0.5 grains per gallon
Soft

There are not enough monitoring sites within 10 miles of Burlington, so this page uses the Skagit County median.

Burlington tap water at a glance

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 9 mg/L means at home

  • Water softener: A water softener is generally not needed. Soft water rarely causes scale.
  • Dishwasher: set the water hardness to about 0.5 gpg (0.5 °dH), which is the lowest hardness setting (or softener off).
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites8
Lab samples51
Sample years2004–2015
Middle 50% of sites7–17 mg/L
Surface water (rivers, lakes)9 mg/L · 8 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Burlington

Prefilled with Burlington's measured local hardness of 9 mg/L (0.5 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Burlington tap water

Burlington is served by more than one water system. These systems supply ZIP codes in Burlington and were tested for PFAS ("forever chemicals") in EPA's nationwide UCMR 5 study. Check your water bill to see which one is yours.

Water systems serving Burlington

Water systemPFAS detectedHighest PFOA / PFOSTested
Skagit County Pud 1 Judy Res
serves over 10,000 people
PFBA — Aug 2024 – May 2025

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Burlington

Burlington is served by more than one water system. Their service line inventories, as reported to EPA:

Water systems serving Burlington

Water systemService linesTotal
Skagit County Pud 1 Judy Res0 lead · 5 galvanized · 0 unknown26,902

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Burlington drinking water violations

Burlington is served by more than one water system. Health-based violations recorded by EPA since 2016:

Water systems serving Burlington

Water systemHealth-based violationsMonitoring/reporting
Skagit County Pud 1 Judy ResNone2

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Burlington

SiteTypeDistanceMedianSamplesYears
EF NOOKACHAMPS CREEK AT HWY 9 NR CLEAR LAKE, WA
USGS Washington Water Science Center
Stream 3.8 mi45 mg/L102015
SAMISH RIVER NEAR BURLINGTON
Washington Department Of Ecology
River/Stream 5.5 mi34 mg/L62009–2010

Water hardness in towns near Burlington

TownDistanceMedianClass
Mount Vernon3 mi 9 mg/LSoft
Sedro-Woolley5 mi 9 mg/LSoft
Anacortes14 mi 9 mg/LSoft
Oak Harbor18 mi 289 mg/LVery hard
Bellingham21 mi 120 mg/LHard
Arlington22 mi 36 mg/LSoft
Marysville28 mi 29 mg/LSoft
Ferndale29 mi 132 mg/LHard
Port Townsend32 mi 25 mg/LSoft
Lake Stevens34 mi 37 mg/LSoft

Skagit County

Burlington is in Skagit County, where the median is 9 mg/L (soft) across 8 sites.

See all of Skagit County →

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next