Water hardness in Pullman, WA

Water in Pullman is moderately hard, with a median of 114 mg/L (6.7 grains per gallon) across Whitman County.

54% harder than the Washington median (74 mg/L) 10th hardest of 122 Washington towns Population 32,863
114mg/L
6.7 grains per gallon
Moderately hard

There are not enough monitoring sites within 10 miles of Pullman, so this page uses the Whitman County median.

Pullman tap water at a glance

  • HardnessModerately hard (114 mg/L, 6.7 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →
  • PFASNone found in EPA's nationwide testing of the main water system.PFAS results →
  • Lead pipesNo lead service lines reported.Details →
  • ViolationsNo health-based violations since 2016.EPA record →

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 114 mg/L means at home

  • Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
  • Dishwasher: set the water hardness to about 6.7 gpg (6.4 °dH), which is a low-to-medium hardness setting.
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites13
Lab samples45
Sample years2000–2016
Middle 50% of sites110–197 mg/L
Groundwater (wells, springs)132 mg/L · 11 sites
Surface water (rivers, lakes)112 mg/L · 2 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Pullman

Prefilled with Pullman's measured local hardness of 114 mg/L (6.7 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Pullman tap water

City of Pullman Water Department is the main public water system for Pullman. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 10 samples taken Mar 2023 – Sep 2023. No PFAS were found at or above EPA's minimum reporting levels.

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Pullman

City of Pullman Water Department reported 5,640 service lines (the pipes connecting homes to the water main) in its inventory. It reported no lead or galvanized lines requiring replacement.

0lead (0%)
0galvanized requiring replacement
0unknown material (0%)
5,640not lead (100%)

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Pullman drinking water violations

EPA records show no health-based violations for City of Pullman Water Department since 2016. It also had 8 monitoring or reporting violations (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Pullman

SiteTypeDistanceMedianSamplesYears
SF PALOUSE RIVER AT PULLMAN
Washington Department Of Ecology
River/Stream 0.6 mi111 mg/L52011–2012
15N/43E-23K01 SU14
USGS Washington Water Science Center
Well 9.3 mi144 mg/L22002–2014

Water hardness in towns near Pullman

TownDistanceMedianClass
Cheney56 mi 24 mg/LSoft
Spokane Valley64 mi 22 mg/LSoft
Liberty Lake65 mi 22 mg/LSoft
Spokane66 mi 70 mg/LModerately hard
Airway Heights66 mi 90 mg/LModerately hard
Walla Walla72 mi 58 mg/LSoft
Pasco98 mi 278 mg/LVery hard
Kennewick102 mi 134 mg/LHard
Moses Lake103 mi 196 mg/LVery hard
Richland106 mi 220 mg/LVery hard

Whitman County

Pullman is in Whitman County, where the median is 114 mg/L (moderately hard) across 13 sites.

See all of Whitman County →

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Pullman, WA water: common questions

Do I need a water softener in Pullman?

Probably not. Water measured around Pullman is 6.7 gpg (114 mg/L, measured locally), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable. If spotting bothers you, about 12,000 grains of capacity covers a 3-person home between weekly regenerations.Size it for your household →

Who supplies Pullman's drinking water?

The main public water system serving Pullman in EPA records is City of Pullman Water Department. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →

Do I need a water filter in Pullman?

Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next