Water hardness in Benton County, OR
Water in Benton County is moderately hard, with a median of 118 mg/L (6.9 grains per gallon) across 59 monitoring sites.
Benton County water at a glance
- HardnessModerately hard (118 mg/L, 6.9 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 118 mg/L means at home
- Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
- Dishwasher: set the water hardness to about 6.9 gpg (6.6 °dH), which is a low-to-medium hardness setting.
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Benton County
Prefilled with Benton County's measured local hardness of 118 mg/L (6.9 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Benton County on the Oregon map
Cities and communities in Benton County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Corvallis | 118 | Moderately hard | 71 sites within 10 miles |
| Albany | 116 | Moderately hard | 76 sites within 10 miles |
| Philomath | 118 | Moderately hard | 62 sites within 10 miles |
| Adair Village | 118 | Moderately hard | 68 sites within 10 miles |
| Monroe | 128 | Hard | 58 sites within 10 miles |
| Alpine (CDP) | 128 | Hard | 39 sites within 10 miles |
| Alsea (CDP) | 118 | Moderately hard | county median |
| Summit (CDP) | 118 | Moderately hard | county median |
| Bellfountain (CDP) | 133 | Hard | 30 sites within 10 miles |
| Kings Valley (CDP) | 118 | Moderately hard | county median |
| Blodgett (CDP) | 118 | Moderately hard | county median |
Water quality in Benton County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Corvallis | City of Corvallis | None detected | 0 lead · 0 unknown | None |
| Albany | City of Albany | None detected | 0 lead · 0 unknown | None |
| Philomath | Philomath Public Works | None detected | 0 lead · 0 unknown | None |
| Adair Village | Adair Village Water System | None detected | 0 lead · 0 unknown | None |
| Monroe | City of Monroe | Not tested | 0 lead · 0 unknown | 27 |
Neighboring counties
- Lincoln County22 mg/L
- Polk County38 mg/L
- Linn County117 mg/L
- Lane County95 mg/L
- Marion County44 mg/L
- Yamhill County96 mg/L
Hardness scale
What to read next
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.