Water hardness in Pike County, AL

Water in Pike County is soft, with a median of 24 mg/L (1.4 grains per gallon) across 12 monitoring sites.

47% softer than the Alabama median (45 mg/L) 46th hardest of 67 counties
24mg/L
1.4 grains per gallon
Soft

Pike County water at a glance

  • HardnessSoft (24 mg/L, 1.4 gpg, local measurements). A water softener isn't needed.Water heater care →
  • Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →

What 24 mg/L means at home

  • Water softener: A water softener is generally not needed. Soft water rarely causes scale.
  • Dishwasher: set the water hardness to about 1.4 gpg (1.3 °dH), which is the lowest hardness setting (or softener off).
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites12
Lab samples111
Sample years2004–2024
Middle 50% of sites15–68 mg/L
Surface water (rivers, lakes)24 mg/L · 12 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Pike County

Prefilled with Pike County's measured local hardness of 24 mg/L (1.4 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

Pike County on the Alabama map

Perry CountyLowndes CountyHouston CountyPickens CountyRandolph CountyButler CountyLamar CountyClay CountyCoffee CountyHenry CountyDale CountyBlount CountyColbert CountyCalhoun CountyTallapoosa CountyFayette CountyEtowah CountyConecuh CountyMorgan CountyMonroe CountyLauderdale CountyRussell CountyBaldwin CountyCleburne CountyDallas CountyDeKalb CountyCherokee CountyMacon CountyBibb CountyFranklin CountyLimestone CountyBarbour CountyWalker CountyMarengo CountyElmore CountyChilton CountyWashington CountyMadison CountyCrenshaw CountyLee CountyMontgomery CountyBullock CountyCullman CountyCoosa CountyGeneva CountyShelby CountyEscambia CountyHale CountyWinston CountyClarke CountyJackson CountyJefferson CountyAutauga CountyMobile CountyLawrence CountyTalladega CountyWilcox CountyTuscaloosa CountySt. Clair CountyChambers CountySumter CountyMarshall CountyCovington CountyMarion CountyGreene CountyChoctaw County

Cities and communities in Pike County

PlaceMedian mg/LClassBased on
Troy 35 Soft 7 sites within 10 miles
Brundidge 35 Soft 9 sites within 10 miles
Goshen 36 Soft 4 sites within 10 miles
Banks 24 Soft 7 sites within 10 miles

Water quality in Pike County communities

Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology

CommunityWater systemPFASLead linesViolations
Troy Troy Utilities (City of) None detected 0 lead · 38 unknown None
Brundidge City of Brundidge Water Department None detected 0 lead · 21 unknown 1
Goshen Goshen Water Works Dist System Not tested 0 lead · 0 unknown None
Banks Banks Water System Not tested 0 lead · 8 unknown None

Neighboring counties

Alabama

The statewide median is 45 mg/L (soft) from 2,227 sites.

Alabama hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next