Water hardness in SeaTac, WA

Water in SeaTac is moderately hard, with a median of 77 mg/L (4.5 grains per gallon) across 8 monitoring sites within 10 miles.

about the same as the Washington median (74 mg/L) 33rd hardest of 122 Washington towns Population 31,799
77mg/L
4.5 grains per gallon
Moderately hard

SeaTac tap water at a glance

  • HardnessModerately hard (77 mg/L, 4.5 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 77 mg/L means at home

  • Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
  • Dishwasher: set the water hardness to about 4.5 gpg (4.3 °dH), which is a low-to-medium hardness setting.
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites8
Lab samples64
Sample years2000–2016
Middle 50% of sites50–108 mg/L
Groundwater (wells, springs)51 mg/L · 3 sites
Surface water (rivers, lakes)78 mg/L · 5 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for SeaTac

Prefilled with SeaTac's measured local hardness of 77 mg/L (4.5 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in SeaTac tap water

SeaTac is served by more than one water system. These systems supply ZIP codes in SeaTac and were tested for PFAS ("forever chemicals") in EPA's nationwide UCMR 5 study. Check your water bill to see which one is yours.

Water systems serving SeaTac

Water systemPFAS detectedHighest PFOA / PFOSTested
Highline Water District
serves over 10,000 people
None detected — Aug 2024 – May 2025
King County Water District #20
serves over 10,000 people
None detected — Mar 2024 – Dec 2024
King County Water District #125
serves over 10,000 people
None detected — May 2023 – Feb 2024
Tukwila Water Department
serves over 10,000 people
None detected — Mar 2024 – Dec 2024
Port of Seattle/Seatac Airport
serves over 10,000 people
None detected — Sep 2023 – Jun 2024

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in SeaTac

SeaTac is served by more than one water system. Their service line inventories, as reported to EPA:

Water systems serving SeaTac

Water systemService linesTotal
Highline Water District0 lead · 0 galvanized · 0 unknown18,780
King County Water District #200 lead · 141 galvanized · 0 unknown10,748
King County Water District #1250 lead · 5 galvanized · 1,194 unknown3,416
Tukwila Water Department0 lead · 0 galvanized · 2,110 unknown2,401
Port of Seattle/Seatac Airport0 lead · 0 galvanized · 2 unknown82

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

SeaTac drinking water violations

SeaTac is served by more than one water system. Health-based violations recorded by EPA since 2016:

Water systems serving SeaTac

Water systemHealth-based violationsMonitoring/reporting
Highline Water DistrictNone0
King County Water District #20None0
King County Water District #125None2
Tukwila Water DepartmentNone0
Port of Seattle/Seatac AirportNone0

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to SeaTac

SiteTypeDistanceMedianSamplesYears
DUWAMISH RIVER AT GOLF COURSE AT TUKWILA, WA
USGS Washington Water Science Center
Stream 3 mi31 mg/L212000–2001
23N/05E-17F01
USGS Washington Water Science Center
Well 5.3 mi51 mg/L12016
MILL CREEK AT EARTHWORKS PARK AT KENT, WA
USGS Washington Water Science Center
Stream 5.4 mi96 mg/L102015
23N/05E-17F04 SWQA13
USGS Washington Water Science Center
Well 5.4 mi48 mg/L12016
MAY CREEK BELOW HONEY DEW CREEK NEAR RENTON, WA
USGS Washington Water Science Center
Stream 7.1 mi78 mg/L102015
21N/04E-07R02 SWQA09
USGS Washington Water Science Center
Well 8.8 mi148 mg/L12016

Water hardness in towns near SeaTac

TownDistanceMedianClass
Tukwila3 mi 87 mg/LModerately hard
Burien3 mi 70 mg/LModerately hard
Des Moines4 mi 58 mg/LSoft
Bryn Mawr-Skyway4 mi 87 mg/LModerately hard
White Center5 mi 67 mg/LModerately hard
Renton5 mi 56 mg/LSoft
Kent6 mi 52 mg/LSoft
Fairwood7 mi 52 mg/LSoft
Lakeland North7 mi 61 mg/LModerately hard
Vashon8 mi 64 mg/LModerately hard

King County

SeaTac is in King County, where the median is 61 mg/L (moderately hard) across 34 sites.

See all of King County →

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next