Water hardness in Wilkin County, MN
Water in Wilkin County is very hard, with a median of 684 mg/L (39.9 grains per gallon) across 7 monitoring sites.
Wilkin County water at a glance
- HardnessVery hard (684 mg/L, 39.9 gpg, local measurements). Water softeners are common at this level.Size a water softener →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 684 mg/L means at home
- Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
- Dishwasher: set the water hardness to about 39.9 gpg (38.3 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
- Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
- Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
- Water heater: flush the tank once a year to clear sediment and scale.
Size a softener for your home → Hard water and your water heater →
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Wilkin County
Prefilled with Wilkin County's measured local hardness of 684 mg/L (40 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Wilkin County on the Minnesota map
Cities and communities in Wilkin County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Breckenridge | 250 | Very hard | 5 sites within 10 miles |
| Rothsay | 684 | Very hard | county median |
| Campbell | 684 | Very hard | county median |
| Foxhome | 684 | Very hard | county median |
| Wolverton | 684 | Very hard | county median |
| Nashua | 1,270 | Very hard | 4 sites within 10 miles |
| Kent | 1,270 | Very hard | 3 sites within 10 miles |
| Doran | 245 | Very hard | 3 sites within 10 miles |
Water quality in Wilkin County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Breckenridge | Breckenridge | None detected | 43 lead · 0 unknown | None |
| Rothsay | Rothsay | Not tested | 0 lead · 174 unknown | None |
| Campbell | Campbell | Not tested | 1 lead · 129 unknown | None |
| Wolverton | Wolverton | Not tested | 2 lead · 105 unknown | None |
| Kent | Kent | Not tested | 0 lead · 56 unknown | None |
Neighboring counties
- Otter Tail County210 mg/L
- Clay County360 mg/L
- Grant County400 mg/L
- Traverse County815 mg/L
- Becker County170 mg/L
- Douglas County222 mg/L
Hardness scale
What to read next
- Do you need a water softener?Water here is very hard; size a softener with our calculator.
- Hard water and your water heaterHow scale affects your water heater and how often to flush.
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.