Water hardness in Washington County, NE
Water in Washington County is very hard, with a median of 393 mg/L (23 grains per gallon) across 18 monitoring sites.
Washington County water at a glance
- HardnessVery hard (393 mg/L, 23 gpg, local measurements). Water softeners are common at this level.Size a water softener →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 393 mg/L means at home
- Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
- Dishwasher: set the water hardness to about 23 gpg (22 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
- Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
- Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
- Water heater: flush the tank once a year to clear sediment and scale.
Size a softener for your home → Hard water and your water heater →
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Washington County
Prefilled with Washington County's measured local hardness of 393 mg/L (23 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Washington County on the Nebraska map
Cities and communities in Washington County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Blair | 357 | Very hard | 13 sites within 10 miles |
| Arlington | 262 | Very hard | 9 sites within 10 miles |
| Fort Calhoun | 348 | Very hard | 16 sites within 10 miles |
| Kennard | 338 | Very hard | 15 sites within 10 miles |
| Herman | 457 | Very hard | 9 sites within 10 miles |
| Washington | 270 | Very hard | 18 sites within 10 miles |
| Fontanelle (CDP) | 218 | Very hard | 50 sites within 10 miles |
Water quality in Washington County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Blair | City of Blair | 1 found | 22 lead · 1,479 unknown | 6 |
| Arlington | Village of Arlington | None detected | 0 lead · 0 unknown | None |
| Fort Calhoun | City of Fort Calhoun | Not tested | 0 lead · 0 unknown | None |
| Kennard | Village of Kennard | Not tested | 4 lead · 95 unknown | None |
| Herman | Village of Herman | Not tested | 2 lead · 119 unknown | None |
Neighboring counties
- Douglas County269 mg/L
- Dodge County223 mg/L
- Burt County356 mg/L
- Sarpy County259 mg/L
- Saunders County217 mg/L
- Cuming County368 mg/L
Hardness scale
What to read next
- Do you need a water softener?Water here is very hard; size a softener with our calculator.
- Hard water and your water heaterHow scale affects your water heater and how often to flush.
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.