Water hardness in Melrose Park, IL
Water in Melrose Park is very hard, with a median of 277 mg/L (16.2 grains per gallon) across 13 monitoring sites within 10 miles.
Melrose Park tap water at a glance
- HardnessVery hard (277 mg/L, 16.2 gpg, local measurements). Water softeners are common at this level.Size a water softener →
- PFASNone found in EPA's nationwide testing of the main water system.PFAS results →
- Lead pipesThe water system reported 744 lead service lines.Check your own pipe →
- ViolationsNo health-based violations since 2016.EPA record →
Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?
What 277 mg/L means at home
- Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
- Dishwasher: set the water hardness to about 16.2 gpg (15.5 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
- Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
- Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
- Water heater: flush the tank once a year to clear sediment and scale.
Size a softener for your home → Hard water and your water heater →
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Melrose Park
Prefilled with Melrose Park's measured local hardness of 277 mg/L (16.2 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
PFAS in Melrose Park tap water
The City of Melrose Park water system is the main public water system for Melrose Park. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 4 samples taken Sep 2023 – Jun 2024. No PFAS were found at or above EPA's minimum reporting levels.
Other water systems serving parts of Melrose Park
| Water system | PFAS detected | Highest PFOA / PFOS | Tested |
|---|---|---|---|
| Leyden TWSP Water District serves over 10,000 people | None detected | — | Mar 2024 – Dec 2024 |
| Franklin Park serves over 10,000 people | None detected | — | Jul 2023 – Apr 2024 |
| Northlake serves over 10,000 people | None detected | — | Mar 2024 – Dec 2024 |
What these PFAS levels mean → Which water filters remove PFAS →
Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology
Lead pipes in Melrose Park
The City of Melrose Park water system reported 5,056 service lines (the pipes connecting homes to the water main) in its inventory. 744 are lead and 0 are galvanized lines that must be replaced, and 2,326 are still of unknown material.
EPA's 2024 lead rule requires most water systems to replace these lines within 10 years, starting in November 2027 (the rule is being challenged in court). Ask the City of Melrose Park water system whether your address is on its list.
Other water systems serving parts of Melrose Park
| Water system | Service lines | Total |
|---|---|---|
| Leyden TWSP Water District | 110 lead · 93 galvanized · 3 unknown | 2,993 |
| Franklin Park | 1,964 lead · 0 galvanized · 1,927 unknown | 5,986 |
| Northlake | 150 lead · 87 galvanized · 1,447 unknown | 3,093 |
How to tell if your home has a lead pipe → Lead pipes in every state →
As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology
Melrose Park drinking water violations
EPA records show no health-based violations for the City of Melrose Park water system since 2016. It also had 1 monitoring or reporting violation (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.
Other water systems serving parts of Melrose Park
| Water system | Health-based violations | Monitoring/reporting |
|---|---|---|
| Leyden TWSP Water District | None | 5 |
| Franklin Park | None | 5 |
| Northlake | None | 3 |
Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology
Monitoring sites closest to Melrose Park
| Site | Type | Distance | Median | Samples | Years |
|---|---|---|---|---|---|
| ADDISON CREEK AT BELLWOOD, IL USGS Illinois Water Science Center | Stream | 1.5 mi | 237 mg/L | 1 | 2000 |
| Addison Creek illinois epa (State) | River/Stream | 1.5 mi | 306 mg/L | 24 | 2000–2002 |
| Des Plaines River illinois epa (State) | River/Stream | 3.5 mi | 286 mg/L | 24 | 2000–2002 |
| ADDISON CREEK AT 19TH AVENUE AT BROADVIEW, IL USGS Illinois Water Science Center | Stream | 3.7 mi | 298 mg/L | 1 | 2004 |
| SALT CREEK AT WESTERN SPRINGS, IL USGS Illinois Water Science Center | Stream | 5.7 mi | 277 mg/L | 27 | 2000–2001 |
| Salt Creek illinois epa (State) | River/Stream | 5.7 mi | 289 mg/L | 25 | 2000–2002 |
Water hardness in towns near Melrose Park
| Town | Distance | Median | Class |
|---|---|---|---|
| Bellwood | 2 mi | 279 mg/L | Very hard |
| Maywood | 2 mi | 286 mg/L | Very hard |
| River Grove | 2 mi | 276 mg/L | Very hard |
| Northlake | 2 mi | 279 mg/L | Very hard |
| River Forest | 2 mi | 286 mg/L | Very hard |
| Franklin Park | 2 mi | 276 mg/L | Very hard |
| Elmwood Park | 3 mi | 280 mg/L | Very hard |
| Forest Park | 3 mi | 283 mg/L | Very hard |
| Schiller Park | 4 mi | 275 mg/L | Very hard |
| Oak Park | 4 mi | 283 mg/L | Very hard |
Cook County
Melrose Park is in Cook County, where the median is 252 mg/L (very hard) across 63 sites.
See all of Cook County →Melrose Park, IL water: common questions
Do I need a water softener in Melrose Park?
Very likely. Water measured around Melrose Park is 16.2 gpg (277 mg/L, measured locally), above 10.5 gpg (180 mg/L), where softeners are common. For a 3-person home that regenerates weekly, that means a softener of about 28,000 grains.Size it for your household →
Who supplies Melrose Park's drinking water?
The main public water system serving Melrose Park in EPA records is Melrose Park. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →
Do I need a water filter in Melrose Park?
It depends on what you want to remove. In Melrose Park, the system reports 744 lead service lines; if your home has one, a filter certified to remove lead is the usual step until the line is replaced. On the other hand, no PFAS found in EPA testing and no health-based violations since 2016. A water softener is not a filter.Check your own service line →
Hardness scale
What to read next
- Do you need a water softener?Water here is very hard; size a softener with our calculator.
- How to tell if your home has a lead pipe744 lead service lines are reported here.
- Hard water and your water heaterHow scale affects your water heater and how often to flush.
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.