Water hardness in Melbourne, FL

Water in Melbourne is very hard, with a median of 279 mg/L (16.3 grains per gallon) across 80 monitoring sites within 10 miles.

131% harder than the Florida median (121 mg/L) 38th hardest of 316 Florida towns Population 86,960
279mg/L
16.3 grains per gallon
Very hard

Melbourne tap water at a glance

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 279 mg/L means at home

  • Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
  • Dishwasher: set the water hardness to about 16.3 gpg (15.6 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
  • Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
  • Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
  • Water heater: flush the tank once a year to clear sediment and scale.

Where the number comes from

Monitoring sites80
Lab samples2,191
Sample years2000–2019
Middle 50% of sites131–367 mg/L
Groundwater (wells, springs)382 mg/L · 2 sites
Surface water (rivers, lakes)274 mg/L · 78 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Melbourne

Prefilled with Melbourne's measured local hardness of 279 mg/L (16.3 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Melbourne tap water

City of Melbourne is the main public water system for Melbourne. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 4 samples taken Feb 2023 – Jan 2024. 3 PFAS were detected.

ChemicalHighest resultDetected inEPA limit
PFBA
perfluorobutanoic acid
9 ppt 3 of 4 samples —
PFBS
perfluorobutane sulfonic acid
4 ppt 3 of 4 samples —
PFPeA
perfluoropentanoic acid
3.1 ppt 1 of 4 samples —

Other water systems serving parts of Melbourne

Water systemPFAS detectedHighest PFOA / PFOSTested
City of Palm Bay
serves over 10,000 people
PFOS, PFPeA, PFOA +4 more 8.5 / 9.5 ppt Jun 2024 – Jan 2025
West Melbourne WTR SYS(Consec)
serves over 10,000 people
PFBA, PFBS, PFPeA — Dec 2025 – Jun 2026

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Melbourne

City of Melbourne reported 60,477 service lines (the pipes connecting homes to the water main) in its inventory. It reported no known lead lines, but 28,363 lines are still of unknown material.

0lead (0%)
0galvanized requiring replacement
28,363unknown material (47%)
32,114not lead (53%)

Other water systems serving parts of Melbourne

Water systemService linesTotal
City of Palm Bay0 lead · 0 galvanized · 19,375 unknown41,838
West Melbourne WTR SYS(Consec)0 lead · 1 galvanized · 1,367 unknown9,927

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Melbourne drinking water violations

EPA records show no health-based violations for City of Melbourne since 2016. It also had 2 monitoring or reporting violations (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.

Other water systems serving parts of Melbourne

Water systemHealth-based violationsMonitoring/reporting
City of Palm Bay20
West Melbourne WTR SYS(Consec)None14

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Melbourne

SiteTypeDistanceMedianSamplesYears
ELBOW CREEK @ CROTON ROAD
FL Dept. of Environmental Protection, Southeast District
Canal Drainage 0.6 mi252 mg/L62003
IRL AT EAU GALLIE RIVER UPSTREAM AT WEIR
St. Johns River Water Management District
River/Stream 1.6 mi370 mg/L162014–2016
EAU GALLIE RIVER @ CROTON ROAD
FL Dept. of Environmental Protection, Southeast District
River/Stream 1.6 mi318 mg/L62003
EAU GALLIE RIVER @ WICKHAM ROAD
FL Dept. of Environmental Protection, Southeast District
River/Stream 1.7 mi367 mg/L62003
ELBOW CREEK @ APOLLO DRIVE
FL Dept. of Environmental Protection, Southeast District
River/Stream 1.7 mi120 mg/L62003
CRANE CREEK @ EVANS ROAD
FL Dept. of Environmental Protection, Southeast District
River/Stream 1.8 mi350 mg/L52003

Water hardness in towns near Melbourne

TownDistanceMedianClass
West Melbourne4 mi 282 mg/LVery hard
Satellite Beach6 mi 272 mg/LVery hard
Palm Bay10 mi 296 mg/LVery hard
Viera East11 mi 190 mg/LVery hard
Merritt Island14 mi 282 mg/LVery hard
Cocoa Beach15 mi 234 mg/LVery hard
Rockledge15 mi 239 mg/LVery hard
Cocoa19 mi 242 mg/LVery hard
Cape Canaveral20 mi 250 mg/LVery hard
Sebastian25 mi 316 mg/LVery hard

Brevard County

Melbourne is in Brevard County, where the median is 250 mg/L (very hard) across 183 sites.

See all of Brevard County →

Florida

The statewide median is 121 mg/L (hard) from 6,382 sites.

Florida hardness map →

Melbourne, FL water: common questions

Do I need a water softener in Melbourne?

Very likely. Water measured around Melbourne is 16.3 gpg (279 mg/L, measured locally), above 10.5 gpg (180 mg/L), where softeners are common. For a 3-person home that regenerates weekly, that means a softener of about 29,000 grains.Size it for your household →

Who supplies Melbourne's drinking water?

The main public water system serving Melbourne in EPA records is City of Melbourne. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →

Do I need a water filter in Melbourne?

It depends on what you want to remove. In Melbourne, EPA testing found PFBA, PFBS and PFPeA in the main system; filters certified to NSF/ANSI 53 or 58 for PFOA and PFOS reduction can lower PFAS. On the other hand, no lead service lines reported and no health-based violations since 2016. A water softener is not a filter.Filters that remove PFAS →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next