Water hardness in Belton, MO
Water in Belton is very hard, with a median of 241 mg/L (14.1 grains per gallon) across 6 monitoring sites within 10 miles.
Belton tap water at a glance
- HardnessVery hard (241 mg/L, 14.1 gpg, local measurements). Water softeners are common at this level.Size a water softener →
- PFAS1 found in EPA testing; every result with a federal limit was at or below it.PFAS results →
- Lead pipesThe water system reported 2 lead service lines.Check your own pipe →
- ViolationsNo health-based violations since 2016.EPA record →
Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?
What 241 mg/L means at home
- Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
- Dishwasher: set the water hardness to about 14.1 gpg (13.5 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
- Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
- Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
- Water heater: flush the tank once a year to clear sediment and scale.
Size a softener for your home → Hard water and your water heater →
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Belton
Prefilled with Belton's measured local hardness of 241 mg/L (14.1 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
PFAS in Belton tap water
Belton PWS is the main public water system for Belton. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 4 samples taken Jan 2024 – Oct 2024. 1 PFAS was detected.
| Chemical | Highest result | Detected in | EPA limit |
|---|---|---|---|
| PFBA perfluorobutanoic acid | 5.4 ppt | 1 of 4 samples | — |
Other water systems serving parts of Belton
| Water system | PFAS detected | Highest PFOA / PFOS | Tested |
|---|---|---|---|
| Kansas City PWS serves over 10,000 people | PFBA | — | Jan 2024 – Oct 2024 |
What these PFAS levels mean → Which water filters remove PFAS →
Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology
Lead pipes in Belton
Belton PWS reported 691 service lines (the pipes connecting homes to the water main) in its inventory. 2 are lead and 0 are galvanized lines that must be replaced, and 689 are still of unknown material.
EPA's 2024 lead rule requires most water systems to replace these lines within 10 years, starting in November 2027 (the rule is being challenged in court). Ask Belton PWS whether your address is on its list.
Other water systems serving parts of Belton
| Water system | Service lines | Total |
|---|---|---|
| Kansas City PWS | 0 lead · 22,951 galvanized · 24,827 unknown | 177,737 |
How to tell if your home has a lead pipe → Lead pipes in every state →
As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology
Belton drinking water violations
EPA records show no health-based violations for Belton PWS since 2016. It also had 4 monitoring or reporting violations (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.
Other water systems serving parts of Belton
| Water system | Health-based violations | Monitoring/reporting |
|---|---|---|
| Kansas City PWS | 1 | 3 |
Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology
Monitoring sites closest to Belton
| Site | Type | Distance | Median | Samples | Years |
|---|---|---|---|---|---|
| BLUE R AT HOLMES RD, JACKSON CO, MO USGS Kansas Water Science Center | Stream | 4.9 mi | 242 mg/L | 3 | 2002–2003 |
| BLUE R AT 151ST S OF MARTIN CITY, MO USGS Kansas Water Science Center | Stream | 5 mi | 246 mg/L | 2 | 2008 |
| Blue River at Blue Ridge Blvd Ext in KC, MO USGS Missouri Water Science Center | Stream | 5.6 mi | 188 mg/L | 35 | 2002–2009 |
| Indian Creek at Kansas City, Missouri Kansas Department Of Health And Environment (State) | River/Stream | 9.4 mi | 240 mg/L | 99 | 2000–2016 |
| Indian Creek at 103rd St in Kansas City, MO USGS Missouri Water Science Center | Stream | 9.4 mi | 271 mg/L | 12 | 2002–2020 |
| Blue River at Kansas City, MO USGS Missouri Water Science Center | Stream | 9.7 mi | 209 mg/L | 15 | 2002–2019 |
Water hardness in towns near Belton
| Town | Distance | Median | Class |
|---|---|---|---|
| Raymore | 4 mi | 242 mg/L | Very hard |
| Grandview | 4 mi | 242 mg/L | Very hard |
| Lee's Summit | 11 mi | 240 mg/L | Very hard |
| Raytown | 13 mi | 242 mg/L | Very hard |
| Blue Springs | 19 mi | 224 mg/L | Very hard |
| Independence | 21 mi | 123 mg/L | Hard |
| Kansas City | 21 mi | 100 mg/L | Moderately hard |
| Grain Valley | 22 mi | 224 mg/L | Very hard |
| Gladstone | 27 mi | 434 mg/L | Very hard |
| Liberty | 30 mi | 451 mg/L | Very hard |
Cass County
Belton is in Cass County, where the median is 238 mg/L (very hard) across 5 sites.
See all of Cass County →Belton, MO water: common questions
Do I need a water softener in Belton?
Very likely. Water measured around Belton is 14.1 gpg (241 mg/L, measured locally), above 10.5 gpg (180 mg/L), where softeners are common. For a 3-person home that regenerates weekly, that means a softener of about 25,000 grains.Size it for your household →
Who supplies Belton's drinking water?
The main public water system serving Belton in EPA records is Belton PWS. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →
Do I need a water filter in Belton?
It depends on what you want to remove. In Belton, EPA testing found PFBA in the main system; filters certified to NSF/ANSI 53 or 58 for PFOA and PFOS reduction can lower PFAS; the system reports 2 lead service lines; if your home has one, a filter certified to remove lead is the usual step until the line is replaced. On the other hand, no health-based violations since 2016. A water softener is not a filter.Filters that remove PFAS →
Hardness scale
What to read next
- Do you need a water softener?Water here is very hard; size a softener with our calculator.
- Which water filters remove PFAS?EPA tests found 1 PFAS in Belton's main water system.
- How to tell if your home has a lead pipe2 lead service lines are reported here.
- Hard water and your water heaterHow scale affects your water heater and how often to flush.